UV-PROTECTION OIL

BACK

CLEAR PROTECTION FOR VERTICAL STRUCTURES

Highly water and dirt resistant
Environmentally friendly wood finish
410 is safe for humans, plants and animals when dry
Clear and transparent colour finishes available
Microporous, penetrating finish which does not crack, peel or flake
No sanding necessary when topping up coating
Delays natural greying by 12 times in comparison to untreated wood
Looking for a product with Extra active ingredients? View UV-Protection Oil Extra

BUY NOW

Documentation

CLEAR FINISH

410 Clear

Enhances the natural character of the wood. Supports a healthy living environment without the use of biocides to ensure the dry finish is safe for humans, plant and animal.

COLOR FINISHES

424 SPRUCE

UV-Resistance: ★★

425 OAK

UV-Resistance: ★★★

426 LARCH

UV-Resistance: ★★★

427 DOUGLAS FIR

UV-Resistance: ★★★

428 RED CEDAR

UV-Resistance: ★★★

429 NATURAL

UV-Resistance: ★★★

431 LIGHT CEDAR

UV-Resistance: ★★★

432 LIGHT OAK

UV-Resistance: ★★★

FINISH

Clear Finish: 410 clear in a Satin finish.

Transparent Colour Finishes: 8 colours in a Satin* finish.

*Product only available when mixed in selected stores, via the Osmo Tinting Machine.

APPLICATION TOOLS

Osmo Flat Brush or Osmo Microfibre Roller

RECOMMENDED USE

Vertical wood surfaces in outdoor areas

RECOAT

One coat, when signs of wear become visible

SIZES

5ml, 125ml, 750ml, 2.5L, 10L

DRY TIME

12 hours

CLEAN UP

Osmo Brush Cleaner

COVERAGE

18m²/L with one coat

COATS

2 coats

CARE

Osmo Spray Cleaner

SURFACE PREPARATION

Wood surface must be clean, dry and frost-free (moisture content max. 20%). Ideally, surfaces are sanded no finer than a P120 grit grade of sand paper. Sanding to finer grades will reduce required absorbency.

Do not thin. Stir well using a flat stirring stick or spatula before use. If possible, and if the wood is an absorbent species, please apply the first coat to all sides before installation.

Fresh wood containing natural wood ingredients /extractives (eg: Cedar, Larch, Teak, Mahogany or Iroko) are often less absorbent and need to weather off first before applying the product. Please refer to website ‘Suitability’ section for more details. Weathering helps ingredient rich wood become more absorbent and the wood finish adheres optimally. Weathering is also required if ingredient rich wood has been freshly sanded or renovated.

A coloured base coat is recommended, e.g. Natural Oil Woodstain. Coloured base coats can improve UV protection.
For renovations, clean old microporous wood finishes thoroughly. De-grey any weathered bare wood with Osmo Wood Reviver Power-Gel before applying an Osmo exterior product.

Old paints and lacquers must be completely removed. As a general rule, wear a dust mask during sanding works. To maintain absorbency, avoid sanding surfaces finer than a P120 grit. Weather ingredient rich wood after sanding.

The finished surface is influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar surfaces.

Soft wood species like Pine or Spruce are more prone to blue stain, rot and insects. If desired, pre-treat these soft woods if possible on all sides with Osmo WR Base Coat.

METHOD OF APPLICATION

With Osmo Flat Brush or Osmo Microfibre Roller, apply thinly along the wood grain and spread well.

Allow to dry for approx. 12 hours. Cooler temperatures, higher humidity levels or over application will delay drying. Once dry, apply the second coat thinly.

When recoating colour treated surfaces, or for renovation works, one coat applied to the clean and dry surface is usually sufficient.

NOTE

Oils enhance and intensify the natural tone of wood (permanent wet effect).
Depending on the degree of weathering, apply one coat of Osmo UV-Protection-Oil Extra to the cleaned and intact finish after approx. 3-4 years.

Osmo UV-Protection-Oil is best suited to vertical structures whereby there is plenty of water run-off. For areas exposed to strong weathering, such as flat horizontals, weatherboard, post caps or window sills, please expect significantly shorter renovation intervals. Vertical elements mounted onto horizontal wood should have at least a 15 degree angle. Sharp edges must be rounded (radius > 2 mm).
If the greying process has already begun, de-grey the surface with Osmo Wood Reviver Power Gel and refinish the dried surface with 2 thin coats of Osmo UV-Protection-Oil Extra.

To achieve the UV protection factor 12, it is necessary to apply 2 thin coats of UV-Protection-Oil Extra. With only one coat on untreated wood, the life of the coating is significantly shorter.

Using power washers will severely decrease the coverage of the finish and general or multi-purpose cleaners will increase the frequency of maintenance and recoating.

NOTE

Regular Cleaning: Damp cleaning with Osmo Spray-Cleaner or diluted Osmo Decking Cleaner.

Occasional Maintenance: If necessary, intensive cleaning and refreshing using Osmo Wood Reviver Power Gel or Osmo Gard Clean.

Recoating: Simply re-apply one thin coat onto the clean and dry surface when signs of wear become visible.

OSMO FLAT BRUSH

Made with high quality synthetic bristles with soft tips which gives fine control in achieving the desired effect. Exceptional coverage capacities which produce professional looking results every time. Available in 25, 50, 60 and 100 mm sizes.

OSMO SMALL ROLLER SET

Microfibre roller and 60mm natural bristle brush set to ensure high coverage allowing you to apply thinly, thoroughly and evenly along the wood grain and spread well. For first application, two coats is recommended onto a clean and dry surface. For renovation, just one coat is necessary.

Top Tips:

Stir well using a flat stirring stick or spatula.
Sand wood to a final P120 grit sand paper grade. This is the optimal grade for applying Osmo UV Protection-Oils.
For ingredient-rich wood species (eg: Cedar, Iroko, Teak, Mahogany etc.), please allow 12 weeks weathering prior to application.
UV-Protection Oils perform optimally on vertically structured timber. For horizontal sections there will be more maintenance.
On horizontal sections, ensure at least a 15 degree angle to facilitate water run-off. Sharp edges must be rounded (radius > 2 mm).
Over application , lower temperatures and poor ventilation will increase the drying times.
UV rays from the sun help to break down protective lignin surrounding the fibres in the wood. Moisture also helps to deplete the lignin and the wood fibres begin to grey naturally. Osmo UV-Protection Oils delay the greying effect 12 x more effectively than bare timber.
Osmo UV-Protection-Oil 420 Extra is furnished with active biocides to help protect the film coating against the effects from mould, algae and fungal attack. The added biocides do not prevent mould, algae and fungal growth forming on the coating.
If a clear UV protective finish without biocides is desired ( eg for animal enclosures ), use Osmo UV-Protection-Oil 410.
Some timbers like Oak and Chestnut are notoriously rich in natural tannins and these ingredients can blacken surfaces when exposed to moisture, sunlight and iron oxides (eg from wire wool). Horizontal sections are more prone to discolouration whereby moisture can accumulate then escape through a breathable coating like Osmo. As the moisture escapes it lowers the risk of warping however, natural tannins can migrate to the surface and cause some black staining. To help reduce this, try to clean the first signs of tannin spots away from the coating with a damp cloth. Over time, the tannins will deplete and the discolouration will be less problematic. Choosing a darker coloured Osmo UV-Protection oil tint, or Osmo Natural Oil Wood stain ( excluding 701 clear matt) can also help to mask discolouration
Many wood species (eg Larch) contain water-soluble coloured extractives which may leach out naturally when weathered. Bare weathered wood can often be refreshed using Osmo Wood Reviver Power Gel prior to treatment. Always trial apply first.

Additional Information:

Approx. coverage: 18m²/L with one coat
No. of coats: 2
Ideal application temperature: +10°C to 35°C
Drying time: 12hrs.
Sizes: 0.125L, 0.750L, 2.5L

All exterior woods grey into a patina colour over time, but UV-Protection Oil has been developed to slow the greying process by (UV factor) 12 times in comparison to untreated wood. Wood colour will fade over time. To maintain some colour for longer, consider transparent coloured options from Osmo like UV Protection Oil Tints or Natural Oil Wood Stain.

Ideal for windows, doors, cladding, fencing and other vertically structured joinery (not recommended on flat surfaces such as decking).

Natural oil-based and microporous finish does not crack, flake, peel or blister. Water and dirt resistant, moisture regulating and reduces wood swelling and shrinkage.

RECOMMENDED AFTER WEATHERING PERIOD

For the following ingredient rich wood species, a weathering period is recommended to improve absorbency. New or freshly sanded ingredient rich wood requires at least 12 weeks exposure to the exterior elements ( unless otherwise stated below) before application.

After the weathering period, it’s generally recommended to de-grey the bare surface with Osmo Wood Reviver Power-Gel , damp rinse, then clean the surface from the extractive content before application, always trial apply!

For all other ingredient-rich hardwood species not mentioned, please contact us for further information.

ALSO RECOMMENDED

❌ Green Oak: moisture content is often above the maximum 20% recommended.

❌ Idigbo: contains yellow dyes which leaches when the wood becomes wet and stains when in contact within iron.

❌ Other: woods treated with a varnish, lacquer or other surface coatings must be completely sanded before use

ALSO RECOMMENDED

For the following wood types, WR Base Coat is recommended before use.

Accoya®
Kebony®
Pine
Douglas Fir
Spruce

Cedar
Iroko
Mahogany
Teak
Walnut
Ipe
Merbau
Wenge
Rosewood
Sycamore
Pressure-Impregnated Pine
Sapele: 3-4 weeks exposure
Larch: 2-6 weeks exposure. Application of WR Base Coat is recommended before use.