WR BASE COAT

BACK

EVEN MORE PROTECTION

Extremely water repellent
Resistant to blue stain, rot and insect attack
Reduces wood swelling and shrinkage
No future application necessary

BUY NOW

Documentation

FINISH

Clear Base Coat

APPLICATION TOOLS

Osmo Flat Brush or Microfibre Roller

RECOMMENDED USE

Vertically structured exterior wood surfaces, especially softwoods

RECOAT

Once used as the initial first coat, there will be no need to recoat.

SIZES

750ml, 2.5L

DRY TIME

12 hours

CLEAN UP

Osmo Brush Cleaner

COVERAGE

5-6m²/L with one coat

COATS

1, 2 or 3 coats (must be equivalent to 160 ml/m²)

SURFACE PREPARATION

Wood surface must be clean, dry and frost-free (moisture content max. 20%).
Osmo WR Base Coat is ready to use, please do not thin. Stir well before use. Clean old microporous stains thoroughly. Old paints and lacquers must be completely removed. As a general rule, wear a dust mask during sanding works. Reseal container after use. Do not allow this product to reach aquatic environments, the ground or the sewer system.
Protect environment (e.g. soil, plants, aquatic environment) from splashes of Osmo WR Base Coat 4001.
Do not apply in damp conditions or if rain is imminent.

METHOD OF APPLICATION

Apply by (brush or roller) spreading out thinly and evenly along wood texture.
Number of coats required: 2-3, depending on wood species and surface characteristics.
Coat the clean, dry and frost-free wood generously – if possible on all sides.
The product should be applied evenly in order to get best results.
Processing temperature: 10 – 30°C.

NOTE

Osmo WR Base Coat is not to be used alone, instead it is a clear impregnation to protect wood against rot, blue stain and insect attack.
Compatible with all common types of glue and putty (except silicone products). We recommend galvanized, anti-corrosive fasteners.
To guarantee full protection (against UV rays) and the long-lasting beauty of wood, a top coat (e.g. with One Coat Only HSPlus, Natural Oil Woodstain, Country Colour, Opaque White Gloss or UV-Protection-Oil) is required after the impregnation has completely dried.
If the coloured surface should have an external surface protection (film protection), we recommend for non-biocidal wood finishes (One Coat Only HSPlus and Country Colour) a top coat with UV-Protection-Oil Extra.*
*Do not coat white finished surfaces with UV-Protection-Oil Extra.

Using power washers will severely decrease the coverage of the finish and general or multi-purpose cleaners will increase the frequency of maintenance and recoating.

CARE

Regular Cleaning: Damp cleaning with Osmo Decking Cleaner using Osmo Decking Cleaning Brush.

Occasional Maintenance: If necessary, intensive cleaning and refreshing using Osmo Wood Reviver Power Gel or Osmo Gard Clean.

Recoating: Simply re-apply one coat onto the clean and dry surface when signs of wear become visible.

OSMO FLAT BRUSH

Made with high quality synthetic bristles with soft tips which gives fine control in achieving the desired effect. Exceptional coverage capacities which produce professional looking results every time. Available in 25, 50, 60 and 100 mm sizes.

OSMO SMALL ROLLER SET

Microfibre roller and 60mm natural bristle brush set to ensure high coverage allowing you to apply thinly, thoroughly and evenly along the wood grain and spread well. For first application, two coats is recommended onto a clean and dry surface. For renovation, just one coat is necessary.

Top Tips:

WR Base Coat is not a wood finish and is a base coat only. A finishing product from the Osmo range is required within three months.
If possible, although not essential; apply to all sides of the wood to give the strongest protection. Wipe excess from edges with a dry cloth before leaving to dry.
Some applications may raise the wood’s grain, if necessary de-nib to smoothen the surface.
Use biocides safely. Always read the label and product information before use.
Note: 4005 WR Base Coat Aqua is discontinued from 2016 and is super-ceded with an improved oil-based version 4001 WR Base Coat.

Additional Information:

Approx. coverage: 5-6m²/L with one coat
No. of coats: 1
Ideal application temperature: +10°C to 35°C
Drying time: 12hrs.
Sizes: 0.125L, 0.750L, 2.5L

Ideal as extra protection for softwood species for the exterior. A clear wood impregnation which serves as a preventive protection against blue stain, rot and insect attack. Penetrates deeply into the wood – prevents swelling and shrinkage and is extremely water repellent with a very low odour during application and is completely odourless when dry.